Noise blips(artifacts)
-
- Expert
- Posts: 23
- Joined: Tue Oct 22, 2019 4:59 pm
Re: Noise blips(artifacts)
Ok, now it just sounds really really staticky and distorted.
Perhaps my mistake was, I pulled all of the tracks from the other project in Auria local file. Do you think I should pull the tracks directly from my drop box files?
Perhaps my mistake was, I pulled all of the tracks from the other project in Auria local file. Do you think I should pull the tracks directly from my drop box files?
-
- Expert
- Posts: 23
- Joined: Tue Oct 22, 2019 4:59 pm
Re: Noise blips(artifacts)
it’s really hard to tell what’s going on in your case.
In order to troubleshoot this, I strongly suggest that you start with just one track, then bounce it and see if there’s some glitches as you were experiencing. Use a clean audio file in which you can trust, something you know for sure is ok. Try it at 44.1 and 48, to see if there’s any difference. Then start adding some additional tracks until you experience the problem, then that last step should be the cause.
In order to troubleshoot this, I strongly suggest that you start with just one track, then bounce it and see if there’s some glitches as you were experiencing. Use a clean audio file in which you can trust, something you know for sure is ok. Try it at 44.1 and 48, to see if there’s any difference. Then start adding some additional tracks until you experience the problem, then that last step should be the cause.
-
- Expert
- Posts: 588
- Joined: Tue Nov 20, 2018 2:56 pm
Re: Noise blips(artifacts)
I’d recommend a couple of things. Record silence to a track and see if blips occur. Record a sine wave from a synth AU.Rodolfo wrote: ↑Fri Jan 24, 2020 1:24 pmit’s really hard to tell what’s going on in your case.
In order to troubleshoot this, I strongly suggest that you start with just one track, then bounce it and see if there’s some glitches as you were experiencing. Use a clean audio file in which you can trust, something you know for sure is ok. Try it at 44.1 and 48, to see if there’s any difference. Then start adding some additional tracks until you experience the problem, then that last step should be the cause.
-
- Expert
- Posts: 23
- Joined: Tue Oct 22, 2019 4:59 pm
Re: Noise blips(artifacts)
I just remembered something that may be important. All of the tracks were recorded in the garage band app then I exported them out and into auria
-
- Expert
- Posts: 588
- Joined: Tue Nov 20, 2018 2:56 pm
Re: Noise blips(artifacts)
Can you set up a simple test with just one track and one of the files? It will be a lot easier to figure out what is going on if you can find the simplest case that results in the issue.Struggling musician wrote: ↑Fri Jan 24, 2020 2:22 pmI just remembered something that may be important. All of the tracks were recorded in the garage band app then I exported them out and into auria
If you can create a new project and import one of the source files and do a bounce and it has the problem that would simplify debugging.
-
- Expert
- Posts: 23
- Joined: Tue Oct 22, 2019 4:59 pm
Re: Noise blips(artifacts)
I bounced a single test track with no artifacts plus it sounds clear. I tested it on a new project with a sample rate of 48k. I also noticed in importing the file it read “converting sample rate “ in the load bar.
The first time I imported multiple tracks at once and did not receive this message. I won’t know for sure if the problem is solved until I import all the tracks in question and bounce them all but I will import them one at a time.
Thank you.
The first time I imported multiple tracks at once and did not receive this message. I won’t know for sure if the problem is solved until I import all the tracks in question and bounce them all but I will import them one at a time.
Thank you.
-
- Expert
- Posts: 23
- Joined: Tue Oct 22, 2019 4:59 pm
Re: Noise blips(artifacts)
The 44100 sample rate may have been the problem. When I first switched to 48k I imported everything from the project files all at once and the files did not convert to 48k so it sounded distorted. Importing one at a time they all converted. I bounced the tracks with no blips! Yet I also didn’t have any plugins running yet but on the 44100 project I bounced them without plug ins and still got the blips. So I think sample rate was the right answer.
Once I get the entire project processed with plugins, I’ll attempt another bounce and let’s you guys know how it turns out.
Thanks for all of your help
Once I get the entire project processed with plugins, I’ll attempt another bounce and let’s you guys know how it turns out.
Thanks for all of your help
Who is online
Users browsing this forum: No registered users and 1 guest